สินค้าทั้งหมด

Machine a reverse downside chamfer with an angle of 0° to 60°, or a square edge condition a plate up to 100 mm thick at an automatic feed speed of up to 1.4 meters/minute.

Motor Power
230/400 Volt, 3 Phase
5,5KW.( 5500W) 50/60 HZ

Bevel Length
max 59 mm

Bevel Angle
0° – 60°

Plate Thickness
8 – 60 mm (*) 8 – 100 mm

Feeding Speed
0 -1.4 mt/min

Machine a V bevel in a plate up to 200 mm thick for butt welding or edge conditioning with a chamfer angle of 15° to 60° at a automatic feed speed of up to 1.4 meters/minute.  The rigid frame incorporates steel where required and aluminum casting where permissible to optimize strength and ergonomics. The motorized feeding process is achieved over hardened work plates with sliding rollers, all driven by two 90 shore polyurethane wheels. 

Motor Power
230/400 Volt, 3 Phase
4kw (4000W), 50/60 Hz

Bevel Length
max 55 mm

Bevel Angle
15° – 60°

Plate Thickness
8 mm – 60 mm (*) 8 mm – 100 mm / 8 mm – 200 mm

Pipe
Ø min 3000 mm

Feeding Speed
0 -1.4 mt/min

The simple solution for creating and maintaining pipe systems: FEIN pipe milling cutters for precise sawing and cutting results.

- Safe working: The feed can be switched on and off to improve operating safety. The safety slipping clutch protects the feed gearbox from overload.

- Robust quality: The machine is perfectly suited to continuous and regular use in demanding operating conditions.

- Compact and space-saving: The shorter side plates reduce the working space around the pipe, as a result the machine can be used when space is extremely tight.

- Reliable guidance: The machine cuts through welded seams and doesn't slip on twocomponent pipes.

- Efficient and economical: The pipe milling machine is ready for use in no time. All cuts are performed reliably and precisely; the investment pays off thanks to the long service life of the machine.

Hacksaws for pipes up to Ø 440 mm* (with chain extention)

Powerful hacksaw for pipes and profiled sections.

- Ideally suited for trimming pipes and shaped section made of steel, cast-iron, autoclaved aerated concrete and plastics.

- Clamp and feed device available for profiles and pipes from Ø 3-1/8 in [80 mm] to Ø 24 in [400 mm].

- Especially suitable for sandwich material and layers of different materials.
- Adjustable clamping devices permit mitre cuts up to 45° as well.
  * With chain extension.

S/N: 2015-10.027870

ด้ามจับถนัดมือ, ความเร็วรอบสม่ำเสมอ, มีระบบป้องกันมอเตอร์โอเวอร์โหลด, ซอฟท์สตาร์ท, เครื่องตัดการทำงานเมื่อใบติดชิ้นงาน,  หัวเกียร์หมุนได้เพื่อย้ายตำแน่งมือจับตามต้องการ 

สิ่งที่แนบมาด้วย: 1 ด้ามจับ, 1 การ์ดป้องกัน

S/N: 2016-12.014474

สิ่งที่แนบมาด้วย: 1 การ์ดป้องกัน , 1 ด้ามจับ

S/N: 2014-07.025807

ตัดเหล็กได้หนาสุด 5ม.ม.

สิ่งที่แนบมาด้วย : 1 กล่อง , 1 ด้ามจับ

Garant CEE 2 IP44 cable reel for site & industry 25m H07RN-F 3G2,5

-  2-socket cable reel drum with 25m cable length H07RN-F 3G2,5 and IP44 protection against splashing of water
-  Extension cable made from Rubber-Neoprene for outdoors and use on sites
-  Ergonomic cable guide handle for easy rewinding, carrying, and cable storage
-  Robust cable reel (230 V/16 A) with single pole safety cut-off and overheating protection